PrepKiYour AI companion for entrance exam preparation
JEE PHYSICS NOTES

AC basics

JEE · Physics · Alternating Current · Std XII

Summary

An alternating voltage changes direction and size with time. For the usual sinusoidal source the instantaneous value is v = V₀ sin ωt (or V₀ cos ωt), where V₀ is the peak value (amplitude), ω = 2πf = 2π/T is the angular frequency, f the frequency and T the period. In India mains is 220 V, 50 Hz, so T = 20 ms and the peak voltage is about 311 V.

The mean (average) value over a full cycle is zero, because the positive and negative halves cancel. Over a half cycle it is 2V₀/π ≈ 0.637 V₀. A moving-coil (DC) instrument responds to this mean, so it reads zero for pure AC.

Key formulas

Instantaneous value
v = V₀ sin ωt, ω = 2πf = 2π/T
rms from peak (sine only)
V rms = V₀/√2 ≈ 0.707 V₀, I rms = I₀/√2
Mean over half cycle (sine)
2V₀/π ≈ 0.637 V₀ (full-cycle mean = 0)
Form factor (sine)
rms ÷ half-cycle mean = π/(2√2) ≈ 1.11
Time from peak to rms
T/8
Definition of rms
I rms = √( (1/T) ∫₀ᵀ i² dt )
Phasor sum (same frequency)
R = √(A² + B² + 2AB cos θ)
I₁ sin ωt + I₂ cos ωt
amplitude √(I₁² + I₂²), rms √((I₁² + I₂²)/2)
Steady + sine
I rms = √(I_dc² + I₀²/2)
Ramp 0 to I₀ / half-wave rectified
I₀/√3 / I₀/2

What this note covers

  • Instantaneous, peak, mean and rms values
  • Phasors
  • rms value of non-sinusoidal waveforms

Solved past-paper question (JEE 2021)

An AC source rated 220 V, 50 Hz is connected to a resistor. The time taken by the current to change from its maximum to the rms value is:

  1. (A) 2.5 ms
  2. (B) 25 ms
  3. (C) 0.25 ms
  4. (D) 2.5 s

Solution

  1. Write the current as I = I₀ sin ωt. It is maximum when ωt = 90° (π/2).

    I = I₀ sin ωt

    peak: ωt = π/2

  2. It equals the rms value I₀/√2 when sin ωt = 1/√2, the next time at ωt = 135° (3π/4).

    I₀/√2 = I₀ sin ωt → ωt = 3π/4

  3. The phase changes by π/4, which is one-eighth of a cycle.

    Δ(ωt) = π/4 = T/8

  4. At 50 Hz the period is 20 ms, so the time is T/8.

    T = 1/50 s = 20 ms

    t = 20/8 = 2.5 ms

Answer: (A) 2.5 ms

Common mistake: Using the 220 V and the resistor to calculate time. Only the frequency is needed.

The full note has 7 solved questions, 7 practice questions, figures and a topic test. Reading it on PrepKi is free after you log in.

PDF download is included in PrepKi plans. See plans.

More notes in Alternating Current